Finding a puddle under your washing machine is never a good thing. One moment, everything is running fine; the next minute, your laundry room looks like a mini flood zone. That first thought is usually: Do I need a plumber? Or is this a washer thing?
At Barton Appliance Repair, we’ve seen just about every type of leak a washing machine can throw your way. As one of Burnaby’s most trusted appliance repair teams, we’ve handled everything from quick hose swaps to full drain pump replacements. The good news is that not every leak means a major breakdown. In fact, many calls we get are for small, fixable issues you can spot early, if you know what to look for.
So, before you start rearranging your week around a broken washer, here is what might be going on, and when it’s time to bring in a professional for washer repair in Burnaby.
Is It Actually a Leak?
Not every puddle is a disaster. Sometimes the reason for this is condensation from the laundry room, a spilt detergent cap, or water coming in from outside. So before assuming the worst, grab a towel and do a quick check:
- Is the water clean or soapy?
- Is it always in the same spot?
- Does it only show up after a wash cycle?
If it’s clean and consistent, chances are that it’s a washing machine issue, and not just a spill.
Common Reasons Your Washer Is Leaking
1. Loose or Damaged Inlet Hoses
This is one of the top reasons we get calls for washer repair in Burnaby. The hoses that connect your washer to the water supply can crack, loosen, or even pop out over time, especially if they’re old or weren’t installed correctly.
What to check: Take a look behind the machine. Check if the hoses are tightly connected. If there are any signs of moisture near the wall connection or the place where they meet the washer. Are the hoses tightly connected? Any signs of moisture near the wall connection or where they meet the washer?
2. Worn-Out Door Seal (Front-Load Machines)
If you have a front-loader, check the rubber gasket around the door. Over time, it can develop small tears or trap debris that prevents a tight seal, leading to slow, annoying leaks during a cycle.
What to do: Wipe down the gasket and check for cracks or trapped lint. Minor issues can be cleaned; bigger tears may need a replacement.
3. Clogged or Broken Drain Pump
The drain pump pushes water out at the end of each cycle. If it gets clogged (with coins, socks, or just debris), water may leak from the bottom of the washer.
Signs: Water pooling directly under the machine, loud buzzing or grinding sounds, or water left inside the drum after the spin cycle.
4. Overloading the Machine
Yes, this one’s on us. Stuffing the drum past its limit can force water out from places it normally wouldn’t escape, especially on high-spin settings.
Fix: Run smaller loads. If your washer is leaking only when overstuffed, scale back and see if it still happens.
5. Detergent Problems
Using too much detergent, or the wrong kind, can cause over rushing. Excess suds can trickle out of the machine or interfere with drainage.
Fix: Use HE (high-efficiency) detergent for modern washers, and never exceed the marked amount. More soap doesn’t mean cleaner clothes.
Quick Troubleshooting: What You Can Try Before Calling a Pro
Some washer leaks don’t need a technician right away. Here are a few things you can safely check:
- Make sure the machine is level. An uneven washer can wobble and spill during a spin cycle.
- Check the drain hose for cracks or dislodged ends.
- Clean the lint trap or coin trap (if your model has one).
- Tighten all hose connections, both at the machine and the wall.
Still leaking after this? Then it’s time to call someone in.
When You Need a Professional Washer Repair in Burnaby
There is a line between DIY and “this could cause water damage.” Here is when you should stop troubleshooting and book a proper repair:
- The leak persists after checking hoses and leveling the machine.
- You hear grinding or burning smells.
- The washer won’t drain at all.
- It leaks during every cycle, not just occasionally.
Letting leaks go unchecked can damage your flooring, walls, and even cause mold growth. So if the problem keeps showing up, don’t ignore it.
Why Barton Appliance Repair?
We have seen every kind of washer leak in Burnaby, loose hoses, cracked pumps, busted door seals, and others. At Barton Appliance Repair, our goal is to fix the issue fast, explain the cause clearly, and prevent it from happening again.
Here’s why homeowners call us when their washer acts up:
Local Technicians
We’re based right here in Burnaby. We are a team of experienced, trusted repair techs who know the neighborhoods and common machine issues in your area.
Same-Day and Next-Day Appointments
The washer leaks, can’t wait. That’s why we prioritize fast turnaround times. Most repairs are handled within 48 hours of your call.
Honest Pricing
We always give you the full quote up front, no vague “starting from” rates or hidden charges. And if the cost of repair isn’t worth it, we will tell you honestly.
Fully Stocked Vans
Most repairs happen on the spot. We carry common parts for all major brands like LG, Samsung, Whirlpool, Maytag, GE, and Bosch, so you are not stuck waiting a week for a part.
Final Thoughts
A leaking washer can feel like a huge headache, but it doesn’t have to be. Most of the time, the issue is easy to spot, and with the right help, just as easy to fix.
So, if you have mopped up one too many mystery puddles, give Barton Appliance Repair a call. For fast, local washer repair in Burnaby. We have got your back.
